Documents

How to use Bridge AP Alignment via Omada APP

Since the antennas of the EAP Bridge model are directional and operate in pairs, they need to be networked through a mesh; moreover, in the installation scenarios, the two Bridges may be quite far apart. If they are not correctly aligned, it may result in poor connection signals, and it is also difficult for users to align them visually. Therefore, we provide an alignment function to guide users in aligning the two Bridges using RSSI, thereby establishing a better connection.

How to use Bridge AP speed test on Omada Controller via Omada APP

Speed tests are widely used to check home broadband, corporate networks, or mobile data connections. They help users verify whether their network provider delivers the promised bandwidth and diagnose connectivity issues. We have added speed test feature for our bridge AP products via Omada APP. You will learn how to use this feature in this guide.

How to assign a static IP address to the EAP using Omada APP

Learn how to configure a static IP address for your EAP (Omada Access Point) using the Omada APP.

How to separate a large amount of VLAN via Bridge VLAN and SSID VLAN (with VLAN Pool)

Bridge VLAN is a feature that allows multiple VLANs to share a single Layer 3 interface and DHCP pool to reduce gateway resource usage. SSID VLAN binds a specific SSID to one or multiple VLANs for straightforward traffic isolation. By combining Bridge VLAN and SSID VLAN, you can meet the requirements of the apartment or hotel room network design without creating a large number of Layer 3 interfaces.

How to unbind an Omada device from a TP-Link account using Omada App

TP-Link ID provides a unified authentication service, allowing you to use a single email address to log in to TP-Link Community, Omada Cloud, the Training system, and manage TP-Link products with TP-Link Apps such as Aginet, Omada, VIGI, Deco, Tether, Kasa, and Tapo. You can unbind the TP-Link account from devices by removing them via the Omada app. After unbinding, you can re-register the Omada devices to another account (TP-Link ID).

How to find IP address of my Omada Devices

By default, Omada devices use dynamic IP addresses. Whether connected to the internet or not, devices such as EAPs or switches should automatically obtain an IP address as long as they are connected to a local network or a DHCP server. There are different ways to find the IP address of an Omada device. Whether the device is in standalone mode or controller mode, you can also use the Omada APP or Discover Utility to find it.

How to configure Account in Controller mode using Omada App

You may want to configure the account in Controller when you use the Omada App, in this article you will know how to do this step by step.

How to Set Up PPTP & L2TP VPN Server with Omada Gateway Using Omada APP

PPTP is the simplest and most basic type of VPN. L2TP is a more secure VPN protocol built on top of PPTP. Omada Gateway supports acting as a server for both VPN types and offers multiple configuration methods. This document introduces how to configure PPTP and L2TP VPN servers via the Omada App in Controller Mode.

How to set up Site-to-Site Auto IPsec VPN Tunnels on Omada Gateway via Omada Controller using Omada APP

How to configure Link Aggregation for EAP

Learn how to configure Link Aggregation on EAP with this step-by-step guide. Enhance your network performance and redundancy effectively.

How to create a VLAN using Omada App

Creating a VLAN using Omada App just needs a few steps, in this article, you will learn how to set it up.

Getting Started with an Omada Pro Controller

How to Capture Wireless Packets via EAP and Omada Controller

Wireless Packet Capture are very important diagnostic tool to analyze wireless communication between an Access Point (AP) and clients, and troubleshoot issues such as wireless packets loss, weak signal, and roaming failures., etc. Omada APs compatible with Omada Controller v6.0 and above support Over-the-Air (OTA) Capture and Non-Over-the-Air (Normal) Capture. This article will provide a step-by-step guide on how to capture wireless packets by using Omada Software Controller v6.0 and EAP787.

How to configure sFlow on Omada Switches

How to configure QoS on Omada Switches in Standalone Mode

How to configure Webhook on the Omada Controller

How to configure Google LDAP on Omada Gateway

How to configure DNS override on Omada Gateway

How to upgrade firmware of Omada Gateway in controller mode

How to filter events in Omada Central when watching playback