Documentos | Suporte de Rede Omada

Filter

Informações relacionadas a 572 encontradas

Filtrar por:

Relevância

What changes are there in Omada Controller v6 compared to v5?

The objective of this document is to provide with a comprehensive, section-by-section mapping between Omada Controller version 5.x and the re-architected 6.0 user interface.

FAQ

11-01-2025

478

What is the difference between Internal Antenna Mode and External Antenna Mode for Omada EAP?

Some Omada AP devices now support both Internal (Directional) and External (Omnidirectional) antennas. Users can switch between the two as needed using the Antenna Selection Feature. This article introduces the new functionality available on specific Omada EAP devices that enables both Directional and Omnidirectional Antenna operation in Standalone Mode.

Configuration Guide

10-31-2025

344

How to set up an SSID with EoGRE Tunnel using Omada EAP

EoGRE (Ethernet over GRE) is a technology that encapsulates Ethernet frames into GRE tunnels for transmission, commonly used to transport Layer 2 Ethernet data over Layer 3 networks. EAPs compatible with Omada Network V6.0 support this feature. The EAP can encapsulate Ethernet packets from the wireless interface into GRE packets and transmit them through a tunnel to a specified remote endpoint for decapsulation, enabling Layer 2 traffic transmission over a Layer 3 network.

Configuration Guide

10-31-2025

355

How to configure WireGuard VPN in Controller mode using Omada APP

This article demonstrates how to configure a WireGuard VPN between Site HQ and Site STA, where each site is equipped with its own Omada Gateway. By following the configuration steps in Controller mode using the Omada App, administrators can quickly establish a secure and reliable VPN tunnel to connect distributed networks.

Configuration Guide

10-31-2025

903

How to Configure Bluetooth feature on Omada Controller

This article details the principle and advantages of Bluetooth IoT technology and provides specific configuration guidelines and application strategies for Bluetooth IoT.

Configuration Guide

10-30-2025

756

How to configure Forwarding Mode of X2-OLT on Omada Controller

Forwarding Mode is the mode of switchover between two boards of OLT. There are two Forwarding Mode: Load Balance allows two boards work together to get high bandwidth. Link Backup allows two boards work in active/standby mode respectively.

Configuration Guide

10-30-2025

785

How to Create Site in Omada Controller via Open API

The Omada API provides programmatic access to TP-Link’s Omada SDN Controller, enabling integration with external systems and automation of network management tasks. Users can authenticate, query network status, manage devices, control client access, and configure settings without using the Omada web interface. This makes it easier to build automate workflows and integrate Omada with third-party platforms or monitoring tools.

Configuration Guide

10-30-2025

1040

How to edit switch port configuration in Omada Network v6

In the latest V6 Controller, we have made partial changes to the switch port configuration logic. This article primarily introduces how to correctly configure switch ports when using the V6 Controller and provides explanations on key points.

Configuration Guide

10-27-2025

1567

How to configure VLAN with Omada Network v6

We are aware that significant changes regarding LAN settings have been made from Omada Controller v5 to Omada Network v6. This article introduces how to configure the VLAN feature with newest Omada Network v6 to help you establish a better understanding of the workflow of how to configure VLAN with Omada Network v6.

Configuration Guide

10-27-2025

2450

How to Design and Deploy Your Network with Omada Design Hub

Omada Design Hub offers a convenient and visualized platform to easily plan your network and select the most suitable network products to deploy. AI tools are also available to facilitate your planning process.

Configuration Guide

10-24-2025

2053

How to Configure Client Recognition on Omada Controller

Omada SDN 6.0 introduced a function to better recognize wireless client devices. By accessing cloud data, the Omada controller could provide more information about the wireless client, including device type, vendor, OS, and so on.

Configuration Guide

10-24-2025

1672

How to Configure Portal Authentication on Omada Controller using Omada App

This guide provides instructions for configuring portal authentication on Omada Controller using Omada App.

FAQ

10-24-2025

2471

How to Preconfigure WAN Settings on Omada Controller using Omada APP

This guide provides instructions for preconfiguring WAN settings on Omada Controller using Omada APP.

FAQ

10-24-2025

1971

How to use Bridge AP Alignment via Omada APP

Since the antennas of the EAP Bridge model are directional and operate in pairs, they need to be networked through a mesh; moreover, in the installation scenarios, the two Bridges may be quite far apart. If they are not correctly aligned, it may result in poor connection signals, and it is also difficult for users to align them visually. Therefore, we provide an alignment function to guide users in aligning the two Bridges using RSSI, thereby establishing a better connection.

FAQ

10-22-2025

2106

How to use Bridge AP speed test on Omada Controller via Omada APP

Speed tests are widely used to check home broadband, corporate networks, or mobile data connections. They help users verify whether their network provider delivers the promised bandwidth and diagnose connectivity issues. We have added speed test feature for our bridge AP products via Omada APP. You will learn how to use this feature in this guide.

FAQ

10-22-2025

2281

How to assign a static IP address to the EAP using Omada APP

Learn how to configure a static IP address for your EAP (Omada Access Point) using the Omada APP.

FAQ

10-10-2025

3286

How to separate a large amount of VLAN via Bridge VLAN and SSID VLAN (with VLAN Pool)

Bridge VLAN is a feature that allows multiple VLANs to share a single Layer 3 interface and DHCP pool to reduce gateway resource usage. SSID VLAN binds a specific SSID to one or multiple VLANs for straightforward traffic isolation. By combining Bridge VLAN and SSID VLAN, you can meet the requirements of the apartment or hotel room network design without creating a large number of Layer 3 interfaces.

Configuration Guide

10-09-2025

3708

How to unbind an Omada device from a TP-Link account using Omada App

TP-Link ID provides a unified authentication service, allowing you to use a single email address to log in to TP-Link Community, Omada Cloud, the Training system, and manage TP-Link products with TP-Link Apps such as Aginet, Omada, VIGI, Deco, Tether, Kasa, and Tapo. You can unbind the TP-Link account from devices by removing them via the Omada app. After unbinding, you can re-register the Omada devices to another account (TP-Link ID).

FAQ

10-09-2025

2470

How to find IP address of my Omada Devices

By default, Omada devices use dynamic IP addresses. Whether connected to the internet or not, devices such as EAPs or switches should automatically obtain an IP address as long as they are connected to a local network or a DHCP server. There are different ways to find the IP address of an Omada device. Whether the device is in standalone mode or controller mode, you can also use the Omada APP or Discover Utility to find it.

Configuration Guide

10-07-2025

6689

How to configure Account in Controller mode using Omada App

You may want to configure the account in Controller when you use the Omada App, in this article you will know how to do this step by step.

FAQ

10-03-2025

2997

Total de itens 572
1
2
3
4
5
•••
29
20 / página