Έγγραφα | Υποστήριξη Δικτύου Omada

Φίλτρο

Βρέθηκαν σχετικές πληροφορίες 407

Ταξινόμηση Κατά:

Σχετικότητα

How to Configure Boundaries and Toggle Simulation Modes in Omada Design Hub

This guide provides instructions for configuring boundaries and toggling bounded/ boundless simulation modes in Omada Design Hub.

Configuration Guide

12-11-2025

212

How to configure Switch QoS in Controller Mode

Omada switch QoS enables prioritized traffic handling via DSCP mapping and SP/WRR scheduling, ensuring optimal performance for critical services like voice and video.

Configuration Guide

12-10-2025

793

How to configure Multicast/Broadcast Rate Limit

Introduces how to configure Multicast/Broadcast Rate Limit.

Configuration Guide

12-10-2025

686

How does multiple PoE out ports work on Omada EAP

This article explains the PoE Out port priority logic and power protection mechanism for devices equipped with dual PoE Out ports that can automatically manage PoE output level.

Configuration Guide

12-09-2025

796

Do I need to use the device with the decorative shell?

For some new Wi-Fi 7 models in the Omada product line, such as the EAP775-Wall 1.0, a decorative shell is included in the package. We recommend using it during installation. The decorative shell primarily enhances the surface temperature experience and, while covering the device’s security lock hole, also allows users to customize the product’s appearance.

Configuration Guide

12-09-2025

785

How to configure storm control in 2.5G Agile Switch

In a network, when client devices generate a large number of Broadcast, Multicast, or Unknown Unicast packets, a broadcast storm may occur, leading to network congestion, latency, or even device disconnection. Storm Control limits the rate of specific packet types to effectively prevent such issues.

Configuration Guide

12-05-2025

1295

How to configure Portal Authentication on Omada Network V6.0 and above

Portal authentication provides authentication service to the clients that only need temporary access to the network, such as the customers in a restaurant or in a supermarket. To access the network, these clients need to enter the authentication login page and use the correct login information to pass the authentication. In addition, you can customize the authentication login page and specify a URL which the authenticated clients will be redirected to.

Configuration Guide

12-04-2025

1493

How to Maintain Management VLAN and Port Settings When Adopting Switches on Omada Network V6

Before Omada Controller V6, when adopting a switch on controller, the default configuration will be applied to the switch and override all the previous pre-configuration done in standalone mode. This could cause inconvenience while adopting switches to a network which management VLAN is not the default VLAN. If the default configuration, especially the default VLAN interface, overrides the pre-configuration done on the switch, it will be disconnected after adoption and hard to recover.

Configuration Guide

11-20-2025

4908

How to set up Site-to-Site Manual IPsec VPN Tunnels on Omada Gateway via Omada Controller using Omada APP

IPsec Site-to-Site VPN can connect geographically isolated networks. It is mainly used in large enterprises to establish VPN channels between branches and the headquarter. IPsec VPN connection is established between branch routers through the public network to transmit private network data.

Configuration Guide

11-20-2025

3400

How to prevent wireless users from sharing Wi-Fi via the mobile hotspot?

Wi-Fi networks are an essential part of modern life, offering connectivity for various devices at home, at work, or in public spaces. However, with the increasing use of Wi-Fi, many individuals share their networks with others, whether intentionally or unintentionally. This can lead to security vulnerabilities, slow speeds, and potential legal issues.

Configuration Guide

11-18-2025

4920

How to Build a Mesh Network via Omada EAP in Controller Mode using Omada APP

In outdoor scenarios where wired networks are difficult to deploy, you can use the mesh function of EAP to extend the coverage of the wireless network. Currently, the mesh function is only supported on APs managed by a controller. This article mainly introduces how to use the APP to operate the controller and complete mesh networking. Depending on the type of controller you are using, the following requirements apply:

Configuration Guide

11-14-2025

4323

How to configure MAC Filtering & MAC Filter in Controller mode using Omada APP

MAC Filtering is a network access control feature that restricts network access by allowing or blocking specific MAC addresses and manages network access behaviors. Currently, MAC Filtering in site settings takes effect on the gateway, while MAC Filter in SSID settings takes effect on the AP or wireless gateway.

Configuration Guide

11-14-2025

3608

How to Configure Hotspot 2.0 Wi-Fi on Omada Controller

This article introduces Hotspot 2.0 Wi-Fi and provides a step-by-step guide on how to configure Hotspot 2.0 on Omada Controller.

Configuration Guide

11-14-2025

4584

How to configure Management VLAN for Omada Devices (Omada Controller 5.15 or above)

The management VLAN is a VLAN created to separate the management network from the data network. By default, the management VLAN is the LAN network in a network centrally managed by Omada SDN Controller. You can change the management VLAN to improve network security. With a separated management VLAN, it is much harder for unauthorized users to modify the configurations or monitor the network.

Configuration Guide

11-13-2025

7195

Interference Detection on Omada Controller

Discover how to use TP-Link Omada’s Interference Detection tool to scan your Wi-Fi network, detect interference sources and analyze channel utilization. This article explains the Interference Detection feature in the Omada Controller, including its purpose, access methods, configuration process and exporting the results.

Configuration Guide

11-08-2025

5674

What should you do when the Omada Network v6 adopts device with outdated firmware?

This article provides a step-by-step guide on what you should do when the Omada Network (v6) adopts device with outdated firmware.

Configuration Guide

11-06-2025

4064

What is the difference between Internal Antenna Mode and External Antenna Mode for Omada EAP?

Some Omada AP devices now support both Internal (Directional) and External (Omnidirectional) antennas. Users can switch between the two as needed using the Antenna Selection Feature. This article introduces the new functionality available on specific Omada EAP devices that enables both Directional and Omnidirectional Antenna operation in Standalone Mode.

Configuration Guide

10-31-2025

4090

How to set up an SSID with EoGRE Tunnel using Omada EAP

EoGRE (Ethernet over GRE) is a technology that encapsulates Ethernet frames into GRE tunnels for transmission, commonly used to transport Layer 2 Ethernet data over Layer 3 networks. EAPs compatible with Omada Network V6.0 support this feature. The EAP can encapsulate Ethernet packets from the wireless interface into GRE packets and transmit them through a tunnel to a specified remote endpoint for decapsulation, enabling Layer 2 traffic transmission over a Layer 3 network.

Configuration Guide

10-31-2025

3410

How to configure WireGuard VPN in Controller mode using Omada APP

This article demonstrates how to configure a WireGuard VPN between Site HQ and Site STA, where each site is equipped with its own Omada Gateway. By following the configuration steps in Controller mode using the Omada App, administrators can quickly establish a secure and reliable VPN tunnel to connect distributed networks.

Configuration Guide

10-31-2025

5308

How to Configure Bluetooth feature on Omada Controller

This article details the principle and advantages of Bluetooth IoT technology and provides specific configuration guidelines and application strategies for Bluetooth IoT.

Configuration Guide

10-30-2025

4032

Συνολικά ΧΧΧΧ αντικείμενα
1
2
3
4
5
•••
21
20 / page