For Class A Switch with Power Adapter:

FCC compliance information statement

Responsible party: 
TP-Link Systems Inc.
Address: 10 Mauchly, Irvine, CA 92618
Website: https://www.tp-link.com/us/
Tel: +1 626 333 0234
Fax: +1 909 527 6804
E-mail: sales.usa@tp-link.com
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•    Reorient or relocate the receiving antenna.
•    Increase the separation between the equipment and receiver.
•    Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•    Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1)    This device may not cause harmful interference.
2)    This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Product Name: Power Adapter
Model Number: T535131-2-DT / T535243-2-DT
Responsible party: 
TP-Link Systems Inc.
Address: 10 Mauchly, Irvine, CA 92618
Website: https://www.tp‑link.com/us/
Tel: +1 626 333 0234
Fax: +1 909 527 6804
E‑mail: sales.usa@tp‑link.com
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•    Reorient or relocate the receiving antenna.
•    Increase the separation between the equipment and receiver.
•    Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•    Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1)    This device may not cause harmful interference.
2)    This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

We, TP-Link Systems Inc., has determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated.
Issue Date: 2025-07-24

CE Mark Warning    

This is a class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
TP-Link hereby declares that the switch is in compliance with the essential requirements and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2011/65/EU and (EU)2015/863.
The original EU Declaration of Conformity may be found at https://www.tp-link.com/en/support/ce/

UKCA Mark

TP-Link hereby declares that the switch is in compliance with the essential requirements and other relevant provisions of the Electromagnetic Compatibility Regulations 2016 and Electrical Equipment (Safety) Regulations 2016.
The original UK Declaration of Conformity may be found at https://www.tp-link.com/support/ukca.

Industry Canada Statement
CAN ICES-003(A)/NMB-003(A) 

この装置は、クラスA情報技術装置です.この装置を家庭環境で使用すると電波妨害を引き起こすことがあります.この場合には使用者が適切な対策を講ずるよう要求されることがあります.  VCCI‑A

BSMI Notice
安全諮詢及注意事項

•    請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。

•    清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。

•    注意防潮，請勿將水或其他液體潑灑到本產品上。

•    插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。

•    請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。 

•    不要私自拆開機殼或自行維修，如產品有故障請與原廠或代理商聯繫

為避免電磁干擾，本產品不應安裝或使用於住宅環境。

限用物質含有情況標示聲明書

Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних документів та вимогам, що передбачені чинними законодавчими актами України.

Safety Information

•    Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.

•    請勿嘗試拆裝、修理或改裝此設備。如有其他需求，請聯繫我們。

•    Keep the device away from water, fire, humidity or hot environments.

•    將設備遠離水、火、潮濕或高溫的環境。

•    Place the device with its bottom surface downward.

•    將設備底部朝下放置。

•    Do not use damaged charger or USB cable to charge the device.

•    請勿使用損壞的充電器或USB線來供應設備充電。

•    Do not use any other chargers than those recommended.

•    請勿使用推薦充電器以外的任何其他充電器。

•    Adapter shall be installed near the equipment and shall be easily accessible.

•    變壓器應安裝在設備附近且易於操作。

•    Use only power supplies which are provided by manufacturer and in the original packing of this product. If you have any questions, please don't hesitate to contact us. (For switch powered by power adapter)

•    請使用由製造商提供並隨產品原包裝附帶的電源供應器。如果您有任何問題，請隨時與我們聯絡。

•    The PoE ports shall not be used to charge lithium batteries or devices supplied by lithium batteries. 

•    PoE 連接埠不得用於為鋰電池或由鋰電池供電的設備充電。

•    The operating temperature for the device is as follows:

•    設備運作溫度如下：

•    The operating temperature for the power adapter shall be within 0 ˚C to 40 ˚C (32 ˚F to 104 ˚F).

•    電源供應器運作溫度: 0 ˚C ~ 40 ˚C (32 ˚F ~ 104 ˚F)

Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.

For Class A Switch with No Power Adapter:

FCC compliance information statement

Responsible party: 

TP-Link Systems Inc.
Address: 10 Mauchly, Irvine, CA 92618
Website: https://www.tp-link.com/us/
Tel: +1 626 333 0234
Fax: +1 909 527 6804
E-mail: sales.usa@tp-link.com
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•    Reorient or relocate the receiving antenna.
•    Increase the separation between the equipment and receiver.
•    Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•    Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1)    This device may not cause harmful interference.
2)    This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

We, TP-Link Systems Inc., has determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated.
Issue Date: 2025-07-24

CE Mark Warning    

This is a class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
TP-Link hereby declares that the switch is in compliance with the essential requirements and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2011/65/EU and (EU)2015/863.
The original EU Declaration of Conformity may be found at https://www.tp-link.com/en/support/ce/

UKCA Mark

TP-Link hereby declares that the switch is in compliance with the essential requirements and other relevant provisions of the Electromagnetic Compatibility Regulations 2016 and Electrical Equipment (Safety) Regulations 2016.
The original UK Declaration of Conformity may be found at https://www.tp-link.com/support/ukca.

Industry Canada Statement
CAN ICES-003(A)/NMB-003(A) 

この装置は、クラスA情報技術装置です.この装置を家庭環境で使用すると電波妨害を引き起こすことがあります.この場合には使用者が適切な対策を講ずるよう要求されることがあります.  VCCI‑A

BSMI Notice
安全諮詢及注意事項

•    請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。

•    清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。

•    注意防潮，請勿將水或其他液體潑灑到本產品上。

•    插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。

•    請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。 

•    不要私自拆開機殼或自行維修，如產品有故障請與原廠或代理商聯繫

為避免電磁干擾，本產品不應安裝或使用於住宅環境。

限用物質含有情況標示聲明書

Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних документів та вимогам, що передбачені чинними законодавчими актами України.

Safety Information

•    Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.

•    請勿嘗試拆裝、修理或改裝此設備。如有其他需求，請聯繫我們。

•    Keep the device away from water, fire, humidity or hot environments.

•    將設備遠離水、火、潮濕或高溫的環境。

•    Place the device with its bottom surface downward.

•    將設備底部朝下放置。

•    Plug the product into the wall outlets with earthing connection through the power supply cord.

•    透過電源線將產品插入具有接地的牆壁插座上。

•    The plug on the power supply cord is used as the disconnect device, the socket-outlet shall be easily accessible.

•    電源線上的插頭端用途為將設備斷電，插座應在易插拔的位置。

•    The socket-outlet shall be installed near the equipment and shall be easily accessible.

•    插座應安裝在設備附近且易插拔的位置。

•    This equipment can be powered only by equipments that comply with Power Source Class 2 (PS2) or Limited Power Source (LPS) defined in the standard of IEC 62368-1. (Only for switch powered by USB or standard PoE.)

•    這台設備僅能由符合IEC 62368-1標準中定義的電源等級2（PS2）或有限電源（LPS）的設備供電。

•    The operating temperature for the device is as follows:

•    設備運作溫度如下：

•    In Denmark: “Apparatets stikprop skal tilsluttes en stikkontakt med jord som giver forbindelse til stikproppens jord.”

•    In Finland: "Laite on liitettävä suojakoskettimilla varustettuun pistorasiaan." 

•    In Norway: “Apparatet må tilkoples jordet stikkontakt.” 

•    In Sweden: “Apparaten skall anslutas till jordat uttag.” 

Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.

For Class B Switch with Power Adapter:

FCC compliance information statement

Responsible party: 
TP-Link Systems Inc.
Address: 10 Mauchly, Irvine, CA 92618
Website: https://www.tp-link.com/us/
Tel: +1 626 333 0234
Fax: +1 909 527 6804
E-mail: sales.usa@tp-link.com
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•    Reorient or relocate the receiving antenna.
•    Increase the separation between the equipment and receiver.
•    Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•    Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1)    This device may not cause harmful interference.
2)    This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Product Name: Power Adapter
Model Number: T120100-2B1 / T120150-2B1 / T050060-2B1
Responsible party: 
TP-Link Systems Inc.
Address: 10 Mauchly, Irvine, CA 92618
Website: https://www.tp‑link.com/us/
Tel: +1 626 333 0234
Fax: +1 909 527 6804
E‑mail: sales.usa@tp‑link.com
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•    Reorient or relocate the receiving antenna.
•    Increase the separation between the equipment and receiver.
•    Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•    Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1)    This device may not cause harmful interference.
2)    This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

We, TP-Link Systems Inc., has determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated.
Issue Date: 2025-07-24

CE Mark Warning    

TP-Link hereby declares that the switch is in compliance with the essential requirements and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863.
The original EU Declaration of Conformity may be found at https://www.tp-link.com/en/support/ce/

UKCA Mark

TP-Link hereby declares that the switch is in compliance with the essential requirements and other relevant provisions of the Electromagnetic Compatibility Regulations 2016 and Electrical Equipment (Safety) Regulations 2016.
The original UK Declaration of Conformity may be found at https://www.tp-link.com/support/ukca.

Industry Canada Statement
CAN ICES-003(B)/NMB-003(B) 

BSMI Notice
安全諮詢及注意事項

•    請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。

•    清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。

•    注意防潮，請勿將水或其他液體潑灑到本產品上。

•    插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。

•    請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。 

•    不要私自拆開機殼或自行維修，如產品有故障請與原廠或代理商聯繫

限用物質含有情況標示聲明書

Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних документів та вимогам, що передбачені чинними законодавчими актами України.

Safety Information

•    Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.

•    請勿嘗試拆裝、修理或改裝此設備。如有其他需求，請聯繫我們。

•    Keep the device away from water, fire, humidity or hot environments.

•    將設備遠離水、火、潮濕或高溫的環境。

•    Place the device with its bottom surface downward.

•    將設備底部朝下放置。

•    Do not use damaged charger or USB cable to charge the device.

•    請勿使用損壞的充電器或USB線來供應設備充電。

•    Do not use any other chargers than those recommended.

•    請勿使用推薦充電器以外的任何其他充電器。

•    Adapter shall be installed near the equipment and shall be easily accessible.

•    變壓器應安裝在設備附近且易於操作。

•    Use only power supplies which are provided by manufacturer and in the original packing of this product. If you have any questions, please don't hesitate to contact us. (For switch powered by power adapter)

•    請使用由製造商提供並隨產品原包裝附帶的電源供應器。如果您有任何問題，請隨時與我們聯絡。

•    This equipment can be powered only by equipments that comply with Power Source Class 2 (PS2) or Limited Power Source (LPS) defined in the standard of IEC 62368-1.

•    這台設備僅能由符合IEC 62368-1標準中定義的電源等級2（PS2）或有限電源（LPS）的設備供電。

•    The operating temperature for the device is as follows:

•    設備運作溫度如下：

Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.

Explanation of the Symbols on the Product Label

產品標籤上符號的解釋

Note: The product label can be found at the bottom of the product and its I.T.E. power supply. Symbols may vary from products.
注意：產品標籤可以在產品底部和其I.T.E.電源供應器上找到。產品標籤可在產品底部找到。符號可能因產品而異。

Symbol 符號解釋	Explanation 解釋
	Class II equipment Class II 設備
	Class II equipment with functional earthing 具有功能接地的Class II 設備
	Alternating current 交流電
	DC voltage 直流電壓
	Polarity of output terminals 輸出端子極性
	Indoor use only 僅限室內使用
	Dangerous voltage 危險電壓
	Caution, risk of electric shock 注意，有觸電危險
	Energy efficiency Marking 能源效率標示
	Protective earth 保護地線
	Earth 地線
	Frame or chassis 機架接地
	Functional earthing 功能地線
	Caution, hot surface 警告，表面高溫
	Caution 警告
	Operator’s manual 操作手冊
	Stand-by 待機
	“ON”/”OFF” (push-push) 「開」/「關」 ( 按壓式)
	Fuse 保險絲
	Fuse is used in neutral N 保險絲用於中性線N
	RECYCLING This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment. 回收利用 本產品標示有「廢棄電氣電子設備（WEEE）」的分類回收標誌。這表示本產品必須依據歐盟指令 2012/19/EU 進行妥善回收或拆 解，以減少對環境的影響。 使用者可選擇將本產品交給合格的回收機構，或在購買新電器或電子設備時，交回給零售商進行回收處理。
	Caution, avoid listening at high volume levels for long periods 注意，避免長時間以高音量收聽
	Disconnection, all power plugs 斷開所有電源插頭
m	Switch of mini-gap construction 迷你間隙結構開關
µ	Switch of micro-gap construction (for US version) Switch of micro-gap / micro-disconnection construction (for other versions except US) 小間隙結構開關（US版本） 小間隙/小斷開結構的開關（非US版）
ε	Switch without contact gap (Semiconductor switching device) 無接觸間隙的開關（半導體開關設備）

Wall Mounting Requirements

ES206X-M2 / ES210X-M2 / ES206XPP-M2:
To mount the device on a wall, use 2 screws which complies with ANSI B1.1 4#, (5#), 6#, 8# standard and are more than 8.5 mm in length. When the screws are fixed on the wall, the distance between the screw head and the wall should be more than 1.5 mm.

ES205G / ES205GP:
To mount the device on a wall, use 2 screws which complies with ANSI B1.1 4# or 6# standard and are more than 11 mm in length. When the screws are fixed on the wall, the distance between the screw head and the wall should be more than 4.5 mm.

ES206GP / ES208G:
To mount the device on a wall, use 2 screws which complies with ANSI B1.1 4#, (5#), 6# standard and are more than 13 mm in length. When the screws are fixed on the wall, the distance between the screw head and the wall should be more than 1.5 mm.

ES210GMP:
To mount the device on a wall, use 2 screws which complies with ANSI B1.1 4#, (5#), 6# standard and are more than 8.5 mm in length. When the screws are fixed on the wall, the distance between the screw head and the wall should be more than 1.5 mm.