Documents | Assistance réseau Omada

Filtre

Informations relatives à 595 trouvées

Trier par:

Pertinence

What changes are there in Omada Controller v6 compared to v5?

The objective of this document is to provide with a comprehensive, section-by-section mapping between Omada Controller version 5.x and the re-architected 6.0 user interface.

FAQ

11-01-2025

1567

What is the difference between Internal Antenna Mode and External Antenna Mode for Omada EAP?

Some Omada AP devices now support both Internal (Directional) and External (Omnidirectional) antennas. Users can switch between the two as needed using the Antenna Selection Feature. This article introduces the new functionality available on specific Omada EAP devices that enables both Directional and Omnidirectional Antenna operation in Standalone Mode.

Guide de configuration

10-31-2025

878

How to set up an SSID with EoGRE Tunnel using Omada EAP

EoGRE (Ethernet over GRE) is a technology that encapsulates Ethernet frames into GRE tunnels for transmission, commonly used to transport Layer 2 Ethernet data over Layer 3 networks. EAPs compatible with Omada Network V6.0 support this feature. The EAP can encapsulate Ethernet packets from the wireless interface into GRE packets and transmit them through a tunnel to a specified remote endpoint for decapsulation, enabling Layer 2 traffic transmission over a Layer 3 network.

Guide de configuration

10-31-2025

867

How to configure WireGuard VPN in Controller mode using Omada APP

This article demonstrates how to configure a WireGuard VPN between Site HQ and Site STA, where each site is equipped with its own Omada Gateway. By following the configuration steps in Controller mode using the Omada App, administrators can quickly establish a secure and reliable VPN tunnel to connect distributed networks.

Guide de configuration

10-31-2025

1620

How to Configure Bluetooth feature on Omada Controller

This article details the principle and advantages of Bluetooth IoT technology and provides specific configuration guidelines and application strategies for Bluetooth IoT.

Guide de configuration

10-30-2025

1421

Comment configurer le mode de transfert du X2-OLT sur un contrôleur Omada

Forwarding Mode is the mode of switchover between two boards of OLT. There are two Forwarding Mode: Load Balance allows two boards work together to get high bandwidth. Link Backup allows two boards work in active/standby mode respectively.

Guide de configuration

10-30-2025

1240

How to Create Site in Omada Controller via Open API

The Omada API provides programmatic access to TP-Link’s Omada SDN Controller, enabling integration with external systems and automation of network management tasks. Users can authenticate, query network status, manage devices, control client access, and configure settings without using the Omada web interface. This makes it easier to build automate workflows and integrate Omada with third-party platforms or monitoring tools.

Guide de configuration

10-30-2025

1885

Présentation de la page d'édition des ports du switch

In the latest V6 Controller, we have made partial changes to the switch port configuration logic. This article primarily introduces how to correctly configure switch ports when using the V6 Controller and provides explanations on key points.

Guide de configuration

10-27-2025

2624

Comment configurer des VLAN sur le contrôleur V6

We are aware that significant changes regarding LAN settings have been made from Omada Controller v5 to Omada Network v6. This article introduces how to configure the VLAN feature with newest Omada Network v6 to help you establish a better understanding of the workflow of how to configure VLAN with Omada Network v6.

Guide de configuration

10-27-2025

4192

Comment concevoir et déployer votre réseau avec Omada Design Hub

Omada Design Hub offre une plateforme pratique et visuelle qui vous permet de planifier facilement votre réseau et de sélectionner les produits réseau les plus adaptés à déployer. Des outils d'IA sont également disponibles pour faciliter votre processus de planification.

Guide de configuration

10-24-2025

2553

Comment configurer la reconnaissance des clients sur le contrôleur Omada

Omada SDN 6.0 a introduit une fonction permettant de mieux reconnaître les appareils clients sans fil. En accédant aux données dans le cloud, le contrôleur Omada peut fournir davantage d'informations sur le client sans fil, notamment le type d'appareil, le fournisseur, le système d'exploitation, etc.

Guide de configuration

10-24-2025

2137

Comment configurer l'authentification du portail sur le contrôleur Omada à l'aide de l'application Omada

Ce guide fournit des instructions pour configurer l'authentification du portail sur Omada Controller à l'aide de l'application Omada.

FAQ

10-24-2025

2999

Comment préconfigurer les paramètres WAN sur le contrôleur Omada à l'aide de l'application Omada

Ce guide fournit des instructions pour préconfigurer les paramètres WAN sur Omada Controller à l'aide de l'application Omada.

FAQ

10-24-2025

2339

How to use Bridge AP Alignment via Omada APP

Since the antennas of the EAP Bridge model are directional and operate in pairs, they need to be networked through a mesh; moreover, in the installation scenarios, the two Bridges may be quite far apart. If they are not correctly aligned, it may result in poor connection signals, and it is also difficult for users to align them visually. Therefore, we provide an alignment function to guide users in aligning the two Bridges using RSSI, thereby establishing a better connection.

FAQ

10-22-2025

2501

How to use Bridge AP speed test on Omada Controller via Omada APP

Speed tests are widely used to check home broadband, corporate networks, or mobile data connections. They help users verify whether their network provider delivers the promised bandwidth and diagnose connectivity issues. We have added speed test feature for our bridge AP products via Omada APP. You will learn how to use this feature in this guide.

FAQ

10-22-2025

2750

Comment attribuer une adresse IP statique à l'EAP à l'aide de l'application Omada

Apprenez à configurer une adresse IP statique pour votre EAP (Omada Access Point) à l'aide de l'application Omada.

FAQ

10-10-2025

3656

How to separate a large amount of VLAN via Bridge VLAN and SSID VLAN (with VLAN Pool)

Bridge VLAN is a feature that allows multiple VLANs to share a single Layer 3 interface and DHCP pool to reduce gateway resource usage. SSID VLAN binds a specific SSID to one or multiple VLANs for straightforward traffic isolation. By combining Bridge VLAN and SSID VLAN, you can meet the requirements of the apartment or hotel room network design without creating a large number of Layer 3 interfaces.

Guide de configuration

10-09-2025

4177

How to unbind an Omada device from a TP-Link account using Omada App

TP-Link ID provides a unified authentication service, allowing you to use a single email address to log in to TP-Link Community, Omada Cloud, the Training system, and manage TP-Link products with TP-Link Apps such as Aginet, Omada, VIGI, Deco, Tether, Kasa, and Tapo. You can unbind the TP-Link account from devices by removing them via the Omada app. After unbinding, you can re-register the Omada devices to another account (TP-Link ID).

FAQ

10-09-2025

2843

How to find IP address of my Omada Devices

By default, Omada devices use dynamic IP addresses. Whether connected to the internet or not, devices such as EAPs or switches should automatically obtain an IP address as long as they are connected to a local network or a DHCP server. There are different ways to find the IP address of an Omada device. Whether the device is in standalone mode or controller mode, you can also use the Omada APP or Discover Utility to find it.

Guide de configuration

10-07-2025

7413

How to configure Account in Controller mode using Omada App

You may want to configure the account in Controller when you use the Omada App, in this article you will know how to do this step by step.

FAQ

10-03-2025

3290

Total 595 articles
1
2
3
4
5
•••
30
20 / page