Documente | Omada Network Support

Filtre

S-au găsit informații legate de 411

Sortează după:

Relevanță

How to add/change an Omada Gateway to an existing Omada network?

This article is a step-by-step guide for replacing a non-Omada or existing Omada gateway with a new Omada gateway.

Ghid de configurare

12-18-2025

257

How to Design and Deploy Your Network with Omada Design Hub

Omada Design Hub offers a convenient and visualized platform to easily plan your network and select the most suitable network products to deploy. AI tools are also available to facilitate your planning process.

Ghid de configurare

12-17-2025

5676

How to Add Omada Devices to Cloud-Based Controller via Omada APP

This article provides guidance for how to add devices to the Cloud-Based Controller via the Omada APP.

Ghid de configurare

12-16-2025

540

How to Setup Omada EAP in Standalone Mode

This FAQ provides guidance on setting up an Omada EAP in Standalone Mode using either the Web GUI or the Omada App. Omada EAPs deliver flexible wireless coverage for small and medium-sized businesses as well as residential environments and can operate independently or under centralized management via an Omada Controller.

Ghid de configurare

12-16-2025

1078

Introduction to Optical Link Budget Between OLT and ONU

The Optical Link Budget is a critical parameter for evaluating whether an optical signal in a fiber communication system can be successfully received along its transmission path. It covers all optical component losses and the transmit/receive capabilities between the OLT (Optical Line Terminal) and ONU (Optical Network Unit), ensuring stable operation within the design range.

Ghid de configurare

12-16-2025

753

How to configure SSL Certificates for Omada Controller

This guide provides instructions for configuring SSL/TLS certificates on Omada SDN Controller.

Ghid de configurare

12-15-2025

670

How to Configure Boundaries and Toggle Simulation Modes in Omada Design Hub

This guide provides instructions for configuring boundaries and toggling bounded/ boundless simulation modes in Omada Design Hub.

Ghid de configurare

12-11-2025

1875

How to configure Switch QoS in Controller Mode

Omada switch QoS enables prioritized traffic handling via DSCP mapping and SP/WRR scheduling, ensuring optimal performance for critical services like voice and video.

Ghid de configurare

12-10-2025

3015

How to configure Multicast/Broadcast Rate Limit

Introduces how to configure Multicast/Broadcast Rate Limit.

Ghid de configurare

12-10-2025

2551

How does multiple PoE out ports work on Omada EAP

This article explains the PoE Out port priority logic and power protection mechanism for devices equipped with dual PoE Out ports that can automatically manage PoE output level.

Ghid de configurare

12-09-2025

2371

Do I need to use the device with the decorative shell?

For some new Wi-Fi 7 models in the Omada product line, such as the EAP775-Wall 1.0, a decorative shell is included in the package. We recommend using it during installation. The decorative shell primarily enhances the surface temperature experience and, while covering the device’s security lock hole, also allows users to customize the product’s appearance.

Ghid de configurare

12-09-2025

2118

How to configure storm control in 2.5G Agile Switch

In a network, when client devices generate a large number of Broadcast, Multicast, or Unknown Unicast packets, a broadcast storm may occur, leading to network congestion, latency, or even device disconnection. Storm Control limits the rate of specific packet types to effectively prevent such issues.

Ghid de configurare

12-05-2025

2028

How to configure Portal Authentication on Omada Network V6.0 and above

Portal authentication provides authentication service to the clients that only need temporary access to the network, such as the customers in a restaurant or in a supermarket. To access the network, these clients need to enter the authentication login page and use the correct login information to pass the authentication. In addition, you can customize the authentication login page and specify a URL which the authenticated clients will be redirected to.

Ghid de configurare

12-04-2025

2255

How to Maintain Management VLAN and Port Settings When Adopting Switches on Omada Network V6

Before Omada Controller V6, when adopting a switch on controller, the default configuration will be applied to the switch and override all the previous pre-configuration done in standalone mode. This could cause inconvenience while adopting switches to a network which management VLAN is not the default VLAN. If the default configuration, especially the default VLAN interface, overrides the pre-configuration done on the switch, it will be disconnected after adoption and hard to recover.

Ghid de configurare

11-20-2025

6046

How to set up Site-to-Site Manual IPsec VPN Tunnels on Omada Gateway via Omada Controller using Omada APP

IPsec Site-to-Site VPN can connect geographically isolated networks. It is mainly used in large enterprises to establish VPN channels between branches and the headquarter. IPsec VPN connection is established between branch routers through the public network to transmit private network data.

Ghid de configurare

11-20-2025

4122

How to prevent wireless users from sharing Wi-Fi via the mobile hotspot?

Wi-Fi networks are an essential part of modern life, offering connectivity for various devices at home, at work, or in public spaces. However, with the increasing use of Wi-Fi, many individuals share their networks with others, whether intentionally or unintentionally. This can lead to security vulnerabilities, slow speeds, and potential legal issues.

Ghid de configurare

11-18-2025

6016

How to Build a Mesh Network via Omada EAP in Controller Mode using Omada APP

In outdoor scenarios where wired networks are difficult to deploy, you can use the mesh function of EAP to extend the coverage of the wireless network. Currently, the mesh function is only supported on APs managed by a controller. This article mainly introduces how to use the APP to operate the controller and complete mesh networking. Depending on the type of controller you are using, the following requirements apply:

Ghid de configurare

11-14-2025

5003

How to configure MAC Filtering & MAC Filter in Controller mode using Omada APP

MAC Filtering is a network access control feature that restricts network access by allowing or blocking specific MAC addresses and manages network access behaviors. Currently, MAC Filtering in site settings takes effect on the gateway, while MAC Filter in SSID settings takes effect on the AP or wireless gateway.

Ghid de configurare

11-14-2025

4159

How to Configure Hotspot 2.0 Wi-Fi on Omada Controller

This article introduces Hotspot 2.0 Wi-Fi and provides a step-by-step guide on how to configure Hotspot 2.0 on Omada Controller.

Ghid de configurare

11-14-2025

5288

How to configure Management VLAN for Omada Devices (Omada Controller 5.15 or above)

The management VLAN is a VLAN created to separate the management network from the data network. By default, the management VLAN is the LAN network in a network centrally managed by Omada SDN Controller. You can change the management VLAN to improve network security. With a separated management VLAN, it is much harder for unauthorized users to modify the configurations or monitor the network.

Ghid de configurare

11-13-2025

8425

În total 411 iteme
1
2
3
4
5
•••
21
20 / page