Dokumente | Omada Netzwerk Support

Filter

547 verwandte Informationen gefunden

Sortieren nach:

Relevanz

How to Build a Mesh Network via Omada EAP in Controller Mode using Omada APP

In outdoor scenarios where wired networks are difficult to deploy, you can use the mesh function of EAP to extend the coverage of the wireless network. Currently, the mesh function is only supported on APs managed by a controller. This article mainly introduces how to use the APP to operate the controller and complete mesh networking. Depending on the type of controller you are using, the following requirements apply:

Leitfaden zur Konfiguration

11-14-2025

332

How to configure MAC Filtering & MAC Filter in Controller mode using Omada APP

MAC Filtering is a network access control feature that restricts network access by allowing or blocking specific MAC addresses and manages network access behaviors. Currently, MAC Filtering in site settings takes effect on the gateway, while MAC Filter in SSID settings takes effect on the AP or wireless gateway.

Leitfaden zur Konfiguration

11-14-2025

267

How to Configure Hotspot 2.0 Wi-Fi on Omada Controller

This article introduces Hotspot 2.0 Wi-Fi and provides a step-by-step guide on how to configure Hotspot 2.0 on Omada Controller.

Leitfaden zur Konfiguration

11-14-2025

402

How to configure Management VLAN for Omada Devices (Omada Controller 5.15 or above)

The management VLAN is a VLAN created to separate the management network from the data network. By default, the management VLAN is the LAN network in a network centrally managed by Omada SDN Controller. You can change the management VLAN to improve network security. With a separated management VLAN, it is much harder for unauthorized users to modify the configurations or monitor the network.

Leitfaden zur Konfiguration

11-13-2025

991

Interference Detection on Omada Controller

Discover how to use TP-Link Omada’s Interference Detection tool to scan your Wi-Fi network, detect interference sources and analyze channel utilization. This article explains the Interference Detection feature in the Omada Controller, including its purpose, access methods, configuration process and exporting the results.

Leitfaden zur Konfiguration

11-08-2025

2301

How to Fix Black Screens, Lag, Distortion, or Pixelation on IPTVs

This article provides a detailed overview of common causes and troubleshooting methods for IPTV issues such as black screens, lag, image distortion, and pixelation. Based on the practical configuration of TP-Link Omada devices, it offers a systematic, multi-layered diagnostic approach and recommended settings to help you restore video playback quality.

Leitfaden zur Fehlerbehebung

11-08-2025

3097

How to Troubleshoot Slow Channel Switching, Missing Channels, and More in IPTV

This guide introduces common causes and step-by-step troubleshooting for issues such as slow channel switching, missing channels, and multi-device viewing failures in IPTV. It outlines diagnostic methods by device type (e.g., terminal, AP, access/aggregation/core switches, gateway) and provides recommended configuration values and validation approaches.

Leitfaden zur Fehlerbehebung

11-07-2025

3046

What should you do when the Omada Network v6 adopts device with outdated firmware?

This article provides a step-by-step guide on what you should do when the Omada Network (v6) adopts device with outdated firmware.

Leitfaden zur Konfiguration

11-06-2025

1801

What changes are there in Omada Controller v6 compared to v5?

The objective of this document is to provide with a comprehensive, section-by-section mapping between Omada Controller version 5.x and the re-architected 6.0 user interface.

FAQ

11-01-2025

3254

What is the difference between Internal Antenna Mode and External Antenna Mode for Omada EAP?

Some Omada AP devices now support both Internal (Directional) and External (Omnidirectional) antennas. Users can switch between the two as needed using the Antenna Selection Feature. This article introduces the new functionality available on specific Omada EAP devices that enables both Directional and Omnidirectional Antenna operation in Standalone Mode.

Leitfaden zur Konfiguration

10-31-2025

1944

How to set up an SSID with EoGRE Tunnel using Omada EAP

EoGRE (Ethernet over GRE) is a technology that encapsulates Ethernet frames into GRE tunnels for transmission, commonly used to transport Layer 2 Ethernet data over Layer 3 networks. EAPs compatible with Omada Network V6.0 support this feature. The EAP can encapsulate Ethernet packets from the wireless interface into GRE packets and transmit them through a tunnel to a specified remote endpoint for decapsulation, enabling Layer 2 traffic transmission over a Layer 3 network.

Leitfaden zur Konfiguration

10-31-2025

1661

How to configure WireGuard VPN in Controller mode using Omada APP

This article demonstrates how to configure a WireGuard VPN between Site HQ and Site STA, where each site is equipped with its own Omada Gateway. By following the configuration steps in Controller mode using the Omada App, administrators can quickly establish a secure and reliable VPN tunnel to connect distributed networks.

Leitfaden zur Konfiguration

10-31-2025

2873

How to Configure Bluetooth feature on Omada Controller

This article details the principle and advantages of Bluetooth IoT technology and provides specific configuration guidelines and application strategies for Bluetooth IoT.

Leitfaden zur Konfiguration

10-30-2025

2299

How to configure Forwarding Mode of X2-OLT on Omada Controller

Forwarding Mode is the mode of switchover between two boards of OLT. There are two Forwarding Mode: Load Balance allows two boards work together to get high bandwidth. Link Backup allows two boards work in active/standby mode respectively.

Leitfaden zur Konfiguration

10-30-2025

1969

How to Create Site in Omada Controller via Open API

The Omada API provides programmatic access to TP-Link’s Omada SDN Controller, enabling integration with external systems and automation of network management tasks. Users can authenticate, query network status, manage devices, control client access, and configure settings without using the Omada web interface. This makes it easier to build automate workflows and integrate Omada with third-party platforms or monitoring tools.

Leitfaden zur Konfiguration

10-30-2025

3205

How to edit switch port configuration in Omada Network v6

In the latest V6 Controller, we have made partial changes to the switch port configuration logic. This article primarily introduces how to correctly configure switch ports when using the V6 Controller and provides explanations on key points.

Leitfaden zur Konfiguration

10-27-2025

4296

How to configure VLAN with Omada Network v6

We are aware that significant changes regarding LAN settings have been made from Omada Controller v5 to Omada Network v6. This article introduces how to configure the VLAN feature with newest Omada Network v6 to help you establish a better understanding of the workflow of how to configure VLAN with Omada Network v6.

Leitfaden zur Konfiguration

10-27-2025

7048

How to Design and Deploy Your Network with Omada Design Hub

Omada Design Hub offers a convenient and visualized platform to easily plan your network and select the most suitable network products to deploy. AI tools are also available to facilitate your planning process.

Leitfaden zur Konfiguration

10-24-2025

3439

How to Configure Client Recognition on Omada Controller

Omada SDN 6.0 introduced a function to better recognize wireless client devices. By accessing cloud data, the Omada controller could provide more information about the wireless client, including device type, vendor, OS, and so on.

Leitfaden zur Konfiguration

10-24-2025

2984

How to Configure Portal Authentication on Omada Controller using Omada App

This guide provides instructions for configuring portal authentication on Omada Controller using Omada App.

FAQ

10-24-2025

4152

547 Artikel insgesamt
1
2
3
4
5
•••
28
20 / Seite